Serving Duluth, Superior & nearby Minnesota and Wisconsin towns Mon–Sat 7am–6pm (715) 919-7956

Toilet & Faucet Installation and Repair in Duluth, MN & Superior, WI

Toilets that run, rock or leak at the base, and faucets that drip or need replacing. We check the shutoffs and the floor under the toilet before we quote, so the price is for the whole job.

Prefer to text? Text (715) 919-7956 · $95 visit fee, waived when you approve the work

Twin Ports Contracting & Repair installs and repairs toilets and faucets in Duluth, MN and Superior, WI, from running toilets and wax rings to kitchen and bath faucet replacement. Our planning range is $150–$300 for a toilet and $130–$260 for a faucet, plus the fixture, on one flat written quote you approve first; the $95 visit fee is waived when you approve the work.

At a glance
Work includedtoilet installation, running toilet repair, wax ring and flange repair, kitchen faucet replacement
WhereDuluth, MN, Superior, WI and the surrounding towns
Visit fee$95 when a visit is needed, waived once you approve the work; no mileage charge.
Getting startedCall or text (715) 919-7956, or send photos through the quote form.

Updated by Twin Ports Contracting & Repair, Duluth, MN

Most Toilet and Faucet Calls Come Down to Three Parts

A toilet that runs after every flush is usually a worn flapper or a tired fill valve. A toilet that rocks, or a damp spot at its base, is usually a failed wax ring and loose bolts. A faucet that drips is usually a worn cartridge. None of those need a new fixture, and a straight answer about which one you have saves you the cost of a replacement you did not need. When a fixture is cracked, stained through or past its parts, we replace it with the one you bought.

Twin Ports Contracting & Repair does this work in Duluth, MN and Superior, WI as a flat written quote you approve before anything is shut off. Our visit fee is waived when you approve the work. For planning, a toilet installation runs $150–$300 and a faucet replacement $130–$260, each plus the fixture, and the toilet and faucet replacement cost guide shows what moves a job off those numbers. For Duluth's permit rules, rentals and soft floors, see toilet repair in Duluth, MN.

What Our Toilet & Faucet Work Covers

  • Toilet installationOld unit hauled away, new one set and sealed
  • Running toilet repairFlapper, fill valve and supply replaced
  • Wax ring and flange repairRocking or leaking toilets reset on a sound base
  • Kitchen faucet replacementPull-down, single-handle and two-handle
  • Bathroom faucet replacementSingle-hole, centerset and widespread
  • Dripping faucet repairCartridge, seats and aerators
  • Supply lines and shutoff valvesBraided lines and quarter-turn stops
  • Bathroom sink hookupsDrain, trap and pop-up reconnected and tested
  • Kitchen sink hookupsSprayer, soap dispenser and basket strainers
  • Toilet seat and bidet seat swapsFit checked against the bowl shape
  • Outdoor faucet swapsFrost-proof sillcocks in place of worn ones
  • Leak testsEvery connection checked after the water is back on

Common Toilet & Faucet Projects

Toilet & Faucet project examples: compare the work included and the details to confirm before booking.
ProjectWhat's includedGood to know
Toilet installationOld toilet removed and hauled away, flange checked, new wax seal, set level, supply connectedThe fixture is yours to buy; a damaged flange is quoted separately
Running toiletFlapper, fill valve or supply line replaced and adjustedUsually a parts swap, not a new toilet
Faucet replacementOld faucet removed, new one mounted, new supply lines, leak testThe sink hole count has to match the new faucet
Sink hookupFaucet, drain and trap connected on a new vanity top or sinkThe vanity or sink is set first, then connected

A toilet & faucet price starts with photos and measurements. The cost guide gives rough ranges, and the estimator adds up a list before you ask for a quote.

For local prices, see the toilet & faucet replacement cost guide.

How to Measure for a New Toilet Before You Buy

The measurement that decides which toilets fit is the rough-in: the distance from the finished wall behind the toilet to the center of the floor bolts. Measure to the wall, not to the baseboard, or you will be off by the thickness of the trim. Most toilets are built for 12 inches, with 10 and 14 inch models for walls that sit too close or too far. Older Duluth and Superior bathrooms turn up all three, and a 12 inch toilet in a 10 inch space either will not fit or leaves the tank hard against the wall.

Then measure the room, not just the floor. Check how far the bowl can project before it meets a tub, vanity or the door swing, decide between round and elongated, and look at seat height if anyone in the house has trouble sitting down or standing up. Our guide to replacing a toilet or faucet walks through each measurement with a table, and for faucets it covers counting the sink holes and the spacing between them.

Wax Rings, Flanges and a Toilet That Rocks

A toilet sits on a wax ring pressed between the bowl and the flange, the ring on the floor that connects to the drain. When the toilet rocks, the seal breaks, and water seeps out around the base a little at a time. You may see a damp patch, smell sewer gas, or find a stain on the ceiling below. The fix is to pull the toilet, scrape off the old wax, check the flange and the floor around it, and reset the toilet on a new seal with snug bolts.

What we find under the toilet decides the quote. A cracked flange ring can often take a repair ring without cutting the drain pipe. A soft floor means a slow leak has already rotted the subfloor, and that is carpentry before the toilet goes back, which is why a soft spot is worth a call early. If the flange sits below the finished floor, or the drain itself needs cutting, that is pipe work done under the required permit by the right trade. Ceiling damage below gets handled with drywall repair once the leak is stopped.

Kitchen and Bathroom Faucets: Holes, Lines and Leaks

A faucet has to match the sink it goes on. Count the holes in the sink or the vanity top, including any hidden under a cover plate, and measure the spacing. One hole takes a single-handle faucet, three holes four inches apart take a centerset, and wider holes take a widespread model. A faucet with more pieces than the sink has holes will not go in without drilling, and drilling a stone or porcelain top is a job for the shop that made it, not the install.

New supply lines and a leak test are part of every faucet job here, because reusing old lines is how a good faucet ends up dripping under the cabinet. In a kitchen we also reconnect the sprayer, soap dispenser and the basket strainer, and check the trap for a slow leak you may not have noticed. If the whole vanity or sink is dated, replacing it together with the faucet and toilet is often one visit instead of three, and that is the bathroom update to ask about.

Repair the Toilet or Faucet, Replace It, or Call a Plumber?

Most toilet and faucet trouble is a worn part, and a new fixture is the answer only when the fixture itself has failed. Anything that changes the piping goes to the right trade.

Toilet and faucet decisions: common symptoms in Duluth and Superior homes, the usual fix, and who does the work.
What you're seeingLikely causeUsual fixWho handles it
Toilet runs after you flush or refills on its ownWorn flapper or a fill valve that sticksReplace the flapper or fill valve and adjust the water levelUs
Toilet rocks, or there is a damp ring at its baseFailed wax ring or loose bolts, sometimes a cracked flangePull the toilet, check the flange and floor, reset on a new sealUs, with carpentry or pipe work quoted separately if the floor or drain is damaged
Toilet tank or bowl is cracked, or the bowl is stained throughThe fixture itself has failedReplace the toilet and haul the old one awayUs
Faucet drips from the spout or the handleWorn cartridge, seat or washerReplace the cartridge, or the faucet if parts are goneUs
Shutoff valve under the sink or behind the toilet will not closeSeized or corroded old valveReplace the valve before the fixture, then testUs where the piping stays as is; a licensed plumber where the pipe has to change
Wet cabinet or ceiling below with no obvious dripLeak in a drain or a supply line inside the wallLocate the leak, repair the pipe, then repair the finishA licensed plumber first, then us

Older Duluth and Superior Plumbing Under the Sink

In an older house the fixture is rarely the hard part; the valves under it are. Shutoffs that have not been turned in decades can refuse to close or start weeping the first time they move, and galvanized supply pipe behind them can crumble where it is touched. We test every shutoff before the old fixture comes off and tell you right then whether a valve needs replacing.

Where a shutoff or supply pipe has to change, we check what your address needs and who the office requires to pull the permit, and a licensed plumber does the pipe work. The same goes in Duluth and Superior: swapping the fixture is our job, rebuilding the piping behind it is theirs.

Toilet and Faucet Work Across the Twin Ports

Setting a toilet or hanging a faucet is the same physical job on both sides of the bridge, but whether it needs a permit, and who may do the piping if it does, changes with the address. Below is what each office says about a plain swap, with the source, plus the house details that tend to turn a one-hour job into a longer one. Wherever you are, we check what your address needs before we quote.

Duluth: Permits, Rentals and Old Shutoffs

Duluth says reconnecting a faucet or toilet needs no permit when the existing water supply isn't altered, while replacing or installing sinks, showers and tubs does (City of Duluth). Rentals can change who holds the permit. Old shutoffs, soft floors and winter tank sweat are covered in toilet repair, toilet installation and faucet work in Duluth, MN.

Toilet and Faucet Swaps in Superior, WI

Superior names the jobs outright: no permit to replace a sink faucet or reset a toilet when the piping is not altered, and none to replace the working parts inside a toilet, faucet or valve (City of Superior). A new tank fill valve or flapper is exactly that. Plumbing beyond the list needs a city permit (City of Superior), and Wisconsin law bars unlicensed plumbing work except by an owner in the one-family home they own and live in (Wis. Stat. 145.06).

That owner exception is why a landlord in Superior cannot treat a new shutoff valve as a handyman job: if the piping changes, we confirm who handles it before we quote. In the Village of Superior the permit questions go to the village office rather than the city.

Hermantown, Proctor and Rice Lake Houses

Hermantown homes are newer, with a median build year of 1993 against 1951 in Duluth (Census Reporter), so the fixtures are more often worn out than the valves behind them. Proctor's FAQ says an owner may do plumbing only in a building they occupy, and otherwise a licensed plumber does it with a plumbing permit (City of Proctor), so a rental toilet that needs a new flange or valve there is confirmed with the city first. Rice Lake is its own city with its own permit office.

Toilets and Faucets on Septic

Past the city sewer lines, a house drains to its own septic system, which St. Louis County's Onsite Wastewater Division administers (St. Louis County). The University of Minnesota's septic program says to repair leaky faucets and fixtures immediately, because excess water entering the system is the most common cause of failure (UMN Onsite Sewage Treatment Program). A toilet that runs after every flush in Lakewood, Pike Lake or Saginaw is therefore a drain-field problem as well as a water bill, and a flapper replacement is the cheap end of the answer. Riverview and other Douglas County addresses on septic follow the same reasoning.

Cloquet, Esko and Carlton County

The Town of Thomson, which covers Esko and Harney, issues its own building, plumbing and HVAC permits, so a plumbing change on a toilet or sink there goes to the township rather than the county. Cloquet handles its own permits. For a straight fixture swap that leaves the piping alone, the work is the same as in Duluth, and the quote says up front whether your address needs anything more.

The office that governs toilet & faucet work changes from town to town; the Minnesota and Wisconsin permit lists name it, with a phone number and the exemptions it allows.

How the Toilet & Faucet Quote and Job Run

What to Send for a Toilet or Faucet Quote

Photos get the quote moving. Send a shot of the whole fixture, one of the shutoff valves under the sink or behind the toilet, and one of the floor around a toilet's base. If you already bought the fixture, add the model number from the box. Tell us if the toilet rocks, if water shows on the ceiling below, or if the valves have never been turned. For a toilet, the rough-in measurement from the wall to the bolts is the single most useful number.

Before requesting a quote, include: Photos of the fixture and the shutoff valves; The model number if you already bought it; The rough-in distance for a toilet, or the sink hole count for a faucet. Gathering these takes a few minutes; the repair-list planning guide shows an easy order to do it in.

How a Toilet & Faucet Job Works

  1. Send the details. Call (715) 919-7956 or use the quote form; a short description of the toilet & faucet job and a few photos are enough to begin.
  2. Get a flat written quote. Nothing begins until you approve the written quote, and the $95 fee for any visit is waived when you do.
  3. Pick a day. Once the quote is approved, you set the day.
  4. Work done, then a walkthrough. We clean up and go over the finished toilet & faucet work with you, and the workmanship is guaranteed in writing: if it fails, we return and redo it at no charge.

Toilet & Faucet Questions

Is a permit needed to swap a toilet or faucet in Duluth or Superior?

Not for a straight swap that leaves the piping alone. The City of Duluth says reconnecting a faucet or toilet needs no permit as long as the existing water supply is not altered, and Superior's Permits Not Required list covers replacing a sink faucet or resetting a toilet without altering the piping. New or moved supply or drain pipe is different, and we check your address before we quote.

Why does my toilet keep running after I flush?

Almost always the flapper or the fill valve. A flapper that no longer seals lets tank water leak into the bowl, so the fill valve keeps topping it up. A fill valve that sticks lets water run into the overflow tube. Both parts are inexpensive and easy to reach, so a running toilet is usually a repair, not a replacement. If the tank itself is cracked or the bowl is stained through, a new toilet is the better answer.

Should I buy the toilet or faucet myself?

Yes. We install the fixture you buy and do not sell fixtures. Keep the box and receipt until it is installed and tested, in case it turns out to be defective, and send the model number so we can check the fit first. Models whose cartridges, flappers and seats are easy to buy locally are the better long-term choice.

What happens during a toilet or faucet installation?

A straight replacement follows one sequence: shut off the water, remove the old fixture, set the new one and test for leaks. The job grows when the shutoff valves will not close, when the flange is cracked, or when the floor under an old toilet has gone soft from a slow leak. We look at those first and say so on the quote. Parts that have to be ordered for an older fixture are the usual wait.

What if the shutoff valve under my sink will not close?

Then the valve gets replaced before the fixture does, and it is worth knowing before anything is unscrewed. A shutoff that will not close means the whole house supply would have to be shut off to work, and old valves on galvanized pipe can fail when moved. Swapping a shutoff changes the piping, so we check what your address needs, and a licensed plumber handles it when the office or the pipe condition calls for one.

How much does it cost to install a toilet or faucet in Duluth?

Our planning range is $150–$300 for a toilet and $130–$260 for a faucet, with the fixture on top. The toilet figure includes hauling the old one away, and the faucet figure includes new supply lines and a leak test. A damaged flange, seized shutoffs or an unusual sink layout are quoted as their own lines. The flat written quote you approve is the real number.

Can I replace my own toilet?

Yes, if you're comfortable lifting a heavy, fragile fixture and setting it on a new wax ring without rocking. A straight swap needs no permit in Duluth if the water supply isn't altered, or in Superior if the piping isn't altered (permit guide). The trouble spots are a shutoff valve that won't close, a broken flange and a soft floor under the old toilet. If you'd rather hand it off, our toilet installation price includes hauling the old one away, and the flat written quote lists any flange or floor repair separately.

Do I need a plumber to change a faucet?

Not for a like-for-like swap on the existing supply lines; neither Duluth nor Superior requires a permit for it. It is a manageable DIY job with a basin wrench and some patience. It stops being a simple swap when the shutoffs are seized, the new faucet needs a different number of sink holes, or the supply piping has to change, and that work is done under the required plumbing permit. Our planning range for a faucet replacement is $130–$260, plus the faucet.

Is it cheaper to hire a handyman or a plumber to replace a toilet or faucet?

For a straight swap, compare flat quotes rather than titles. Our planning ranges are $150–$300 for a toilet and $130–$260 for a faucet, fixture not included, and bundling both with other small jobs in one visit spreads the trip. Anything that alters the piping is done under the required plumbing permit, and water heaters, gas lines, main drains and emergencies belong with a licensed plumber from the start. Our licensing guide explains the rules.

Does water at the base of the toilet mean the toilet needs replacing?

Usually not. Water at the base usually comes from a failed wax ring, loose floor bolts that let the toilet rock, a dripping supply connection, or a tank that sweats in humid summer weather. Those are repairs: we lift the toilet, check the flange and floor, and reset it on a new seal. Replacement makes sense when the tank or bowl itself is cracked. Don't wait on it, since a slow leak at the base rots the subfloor and stains the ceiling below.

What does it cost to replace a broken toilet flange?

It's quoted as a line on the toilet job, because nobody can see the flange until the toilet comes up. A cracked flange ring can often take a metal repair ring or a bolt-down repair flange without cutting into the drain pipe. If the drain itself needs cutting or replacing, that part is done under the required plumbing permit, and a subfloor rotted by an old leak is carpentry. Our toilet installation planning range is $150–$300, with flange work priced on top.

How high should a toilet be after hip or knee replacement?

Follow your surgeon or occupational therapist first; they may prescribe a raised seat or a toilet safety frame for the first weeks. For a permanent change, a comfort-height toilet puts the seat in the 17- to 19-inch range the U.S. Access Board uses for accessible toilets (Access Board toilet guide), which is a reference point for a home, not a requirement. A grab bar beside it helps too; see safety and mobility.

Can you replace just the tank on a toilet?

Yes, if a matching tank is still available for your bowl. American Standard says a tank or bowl can be replaced on its own when the specific or a compatible model is available (American Standard), but most of its tanks and bowls are built as a set, and a mismatched pair may not flush at all; a 3.5-gallon tank won't work on a 1.6-gallon bowl (American Standard). Have your tank and bowl model numbers in hand before shopping. If no matching tank exists, the whole toilet gets replaced.

Can you install a toilet or faucet I bought online?

Yes. Installing a fixture you bought is a normal labor-only job. Open the box and check for cracks or missing parts before the visit, and keep the packaging until the fixture has been installed and tested. Send the model number first so we can check the rough-in or hole count against what is in your house; a toilet that is the wrong size is cheaper to return before it is carried upstairs.

These answers also sit in the Toilet & Faucet section of our FAQ, alongside questions on pricing, scheduling and coverage.

Town-by-Town Notes for This Work

Each town below has its own page, built around its permit office and the age of its houses.

Where We Work: Our Service Area

Looking for toilet & faucet help near you? Start with your town in the list below.

Duluth neighborhoods:

Superior neighborhoods:

Don't see your town? The surrounding town notes cover the rest of the area for toilet & faucet jobs, and the Minnesota and Wisconsin town guides give a checklist for each one.

Town checklists for toilet & faucet projects

Project notes for towns across the service area:

Stop the Drip, Steady the Toilet

Send a photo of the fixture and the shutoff valves under it, plus the model number if you already bought one, and we'll put a flat price in writing before any work starts.

Prefer to text? Text (715) 919-7956

  • $95 visit fee, waived when you approve the work
  • Same price across the service area
  • Insured, background-checked staff